# moldtraining.us/guides/remove-mold-from-walls/: agent-readable view

How to Remove Mold From Walls: Painted Drywall, Bare Drywall, Plaster and Inside the Wall (free guide)
summary     How to remove mold from walls safely: painted vs. bare drywall, plaster and concrete, when to cut out drywall, checking inside the wall cavity, PPE, the 10 square foot rule, and preventing it from coming back.

sections
- First: why is the wall wet?
- Protect yourself
- By wall type
- Cutting out moldy drywall
- Don't paint over it
- Prevent it coming back

faq
Q: How do you get mold off walls?
A: Fix the moisture first. On painted or non-porous walls with surface spots, scrub with detergent and water and dry. On flat-painted or bare drywall with growth, the affected section usually needs to be cut out and replaced. Wear an N-95, gloves and unvented goggles.
Q: Can moldy drywall be cleaned?
A: Surface spots on sound, glossy-painted drywall can sometimes be cleaned. Mold growing into the paper facing, or drywall that's swollen, soft or stained through, should be removed and replaced.
Q: Can you paint over mold on walls?
A: No. EPA warns that paint over mold will likely peel and growth continues underneath. Clean or remove the mold and fix the moisture first.
Q: When should I call a professional for mold on walls?
A: When the affected area is more than about 10 square feet, the water was contaminated, the HVAC system is involved, mold is inside the wall cavity over a large area, or occupants have health concerns.

note        Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

Courses delivered by HAZWOPER OSHA Training, LLC, an IACET Accredited ProviderDelivered by an IACET Accredited Provider

Free Guide

How to Remove Mold From Walls: Painted Drywall, Bare Drywall, Plaster and Inside the Wall

Whether you can wipe it off or need to cut the wall open depends on the wall material and where the water came from. Here is how to decide and how to do it safely.

  • 7 min read
  • Updated October 25, 2026
On this page
  1. First: why is the wall wet?
  2. Protect yourself
  3. By wall type
  4. Cutting out moldy drywall
  5. Don't paint over it
  6. Prevent it coming back
  7. FAQ

First: why is the wall wet?

Mold on a wall almost always traces back to condensation (cold exterior walls, poor air flow), a leak (plumbing, roof, window), or high humidity. Find and fix the source first, or the mold will return. A moisture meter tells you whether the wall is still wet. See moisture and humidity.

Protect yourself

Wear an N-95 respirator, gloves and goggles without vents. Ventilate the room, keep children and sensitive people away, and never mix bleach with ammonia or vinegar. For areas larger than about 10 square feet, follow EPA's remediation guidance or hire a professional. Check the size with the remediation level tool.

By wall type

WallWhat usually works
Painted drywall (glossy or semi-gloss), surface spots onlyGently scrub with detergent and water, wipe clean, and dry. If the paint is sound and the drywall isn't soft or stained through, that may be enough
Flat-painted or bare drywall with growthDrywall is porous. Growth on the paper facing usually means cutting out and replacing the affected section
Drywall that's swollen, soft, crumbling or stained throughRemove and replace; check inside the cavity
PlasterScrub with detergent and water and dry; plaster that's deteriorated or wet behind should be repaired
Concrete or blockScrub with detergent and water and dry; address the moisture source, such as exterior drainage
Tile, glass, metalScrub with detergent and water and dry

EPA's water damage guidance says drywall wet with clean water may be dried in place only if there's no obvious swelling and the seams are intact; otherwise it should be removed. Once mold is growing in drywall, removal is the usual answer.

Cutting out moldy drywall

  1. Mist the area lightly to keep spores down, and seal the room door and vents with plastic for larger jobs.
  2. Cut out the affected section with a utility knife or saw, extending past the visible growth to sound, dry material.
  3. Bag the debris in heavy plastic inside the room and seal it before carrying it out.
  4. Inspect the cavity: framing, insulation and the back of the drywall. Wet or moldy insulation is discarded.
  5. Clean framing with detergent and water (lightly sand surface growth on wood), HEPA vacuum, and let everything dry completely.
  6. Fix the moisture source, confirm dry readings, then patch.

Don't paint over it

EPA warns against painting or caulking over moldy surfaces. Paint over mold usually peels, and growth continues underneath. Mold-resistant paint can help on clean, dry surfaces in damp rooms, but it's not a fix for existing growth.

Prevent it coming back

  • Keep indoor humidity below 60%, ideally 30 to 50%.
  • Pull furniture a few inches away from exterior walls.
  • Use exhaust fans in bathrooms, kitchens and laundry areas.
  • Insulate and air-seal cold walls where condensation keeps forming.

Sources and official references

Last reviewed: October 25, 2026 · Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

FAQ

Frequently asked questions

Fix the moisture first. On painted or non-porous walls with surface spots, scrub with detergent and water and dry. On flat-painted or bare drywall with growth, the affected section usually needs to be cut out and replaced. Wear an N-95, gloves and unvented goggles.

Surface spots on sound, glossy-painted drywall can sometimes be cleaned. Mold growing into the paper facing, or drywall that's swollen, soft or stained through, should be removed and replaced.

No. EPA warns that paint over mold will likely peel and growth continues underneath. Clean or remove the mold and fix the moisture first.

When the affected area is more than about 10 square feet, the water was contaminated, the HVAC system is involved, mold is inside the wall cavity over a large area, or occupants have health concerns.

Need Documented Mold Training?

Mold Awareness, Property Management and Mold Inspector courses. Certificate of completion. English & Spanish.