# moldtraining.us/free-training/moisture-and-humidity/: agent-readable view

Moisture, Humidity and Condensation: Where Indoor Mold Water Comes From (free lesson 2 of 12)
type        free mini-training lesson with 8-question quiz (graded in-browser, nothing saved)
time        13 minutes
summary     Free lesson on the moisture sources behind indoor mold: leaks, floods, condensation, relative humidity, dew point, and EPA's 30 to 50 percent humidity target. 8-question quiz.

objectives
- Identify the main sources of moisture in buildings
- Explain relative humidity, dew point and condensation
- State EPA's recommended indoor humidity range
- Choose practical moisture controls for property teams

sections
- Four ways water gets in
- Relative humidity
- Dew point and condensation
- Moisture controls for property teams
- Key takeaways

standards   EPA mold and moisture guidance

certificate course  https://moldtraining.us/mold-training-for-property-management/
note        Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

Courses delivered by HAZWOPER OSHA Training, LLC, an IACET Accredited ProviderDelivered by an IACET Accredited Provider

Leer en español

Free Mini-Training · Lesson 2 of 12

Moisture, Humidity and Condensation: Where Indoor Mold Water Comes From

Every mold problem starts with water. Learn the four ways water gets into materials, how condensation works, and the humidity levels EPA recommends.

  • 13 min
  • 8-question quiz
  • Beginner
  • Free · no sign-up
On this page
  1. What you'll learn
  2. Four ways water gets in
  3. Relative humidity
  4. Dew point and condensation
  5. Moisture controls for property teams
  6. Key takeaways
  7. Lesson quiz

In this lesson

What you'll learn

  • Identify the main sources of moisture in buildings
  • Explain relative humidity, dew point and condensation
  • State EPA's recommended indoor humidity range
  • Choose practical moisture controls for property teams

Four ways water gets in

SourceExamplesTypical clue
LeaksRoofs, windows, plumbing, appliance hoses, HVAC drain linesStains, drips, damp drywall
Floods and overflowsStorms, burst pipes, overflowing tubs, sewer backupsStanding water, wet carpet
CondensationCold pipes, windows, exterior walls, ducts, AC coilsBeading water, damp corners, window sill mold
HumidityShowers, cooking, laundry, crowded units, humid climates, crawl spacesMusty smell, mold on many surfaces

Groundwater and rising damp through foundations and slabs, plus building materials installed wet, add to the list.

Relative humidity

Relative humidity (RH) is the amount of water vapor in the air compared with the most the air can hold at that temperature, as a percentage. Warm air can hold more water than cold air, so the same air has a higher RH when it cools.

EPA recommends keeping indoor relative humidity below 60%, ideally between 30% and 50%.

Dew point and condensation

The dew point is the temperature at which air becomes saturated and water starts to condense. When warm, humid indoor air touches a surface colder than the dew point, water condenses on that surface. That's how mold grows on:

  • Cold exterior walls and corners, especially behind furniture where air doesn't circulate.
  • Window frames and sills in winter.
  • Cold water pipes, toilet tanks and AC ducts in summer.

Even when room RH looks acceptable, the air right at a cold surface can be near 100%. Check it with the dew point calculator.

Moisture controls for property teams

  • Fix leaks fast and dry wet materials within 24 to 48 hours.
  • Vent moisture outdoors: bathroom and kitchen exhaust fans ducted to the exterior, and clothes dryers vented outside.
  • Run air conditioning and dehumidifiers in humid seasons; keep AC drip pans clean and drain lines clear.
  • Insulate cold surfaces like pipes and ducts to prevent condensation.
  • Direct water away from the building: gutters, downspouts and grading.
  • Keep crawl spaces dry: vapor retarders on dirt floors, proper ventilation or conditioning.
  • Don't carpet areas that stay damp, such as bathrooms or basements with moisture problems.

Key takeaways

  • Water enters buildings through leaks, floods, condensation and humidity.
  • RH rises as air cools; condensation forms on surfaces colder than the dew point.
  • EPA's target: indoor RH below 60%, ideally 30% to 50%.
  • Dry wet materials within 24 to 48 hours, vent moisture outdoors and insulate cold surfaces.

Knowledge check

Lesson 2 quiz: 8 questions

Choose one answer for each question, then select Check my answers. Score 80% or higher to pass. Your answers stay in your browser and are never saved.

Question 1 What indoor relative humidity range does EPA recommend?
Question 2 What is the dew point?
Question 3 Why does mold often grow on cold exterior walls behind furniture?
Question 4 What happens to relative humidity when air cools without adding or removing moisture?
Question 5 Which is a moisture control for bathrooms?
Question 6 Within what time should water-damaged materials be dried to prevent mold?
Question 7 Which tool tells you whether drywall is wet?
Question 8 A crawl space has a bare dirt floor and musty odors. Which control helps?

Sources and official references

Last reviewed: October 25, 2026 · Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

Need Documented Mold Training?

Mold Awareness, Property Management and Mold Inspector courses. Certificate of completion. English & Spanish.